Versions Compared

Old Version 92

changes.mady.by.user Roman Nazarov

Saved on

compared with

New Version 93

changes.mady.by.user Gleb Matskevich

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

ATM-Intellect

Registry section

String parameter

Available values

Default

Product version

Description

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PeakWorkingSetSizeQuota

>=0

100

from 8.0


The maximum memory size in megabytes used by the process videosrv.exe on ATM-Intellect Pro. If the parameter is set to 0, then the check for the used memory is not performed.

Once a day, the ATM-Intellect Prochecks the size of the memory it uses. The check is performed at the time specified by the TimeOfCheckWorkingSetSize key (see below).

After exceeding the specified value, the videosrv.exe module is rebooted.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeOfCheckWorkingSetSize

>=0

3

from 8.0

Time to check memory usage in hours. Default value is 3 (3:00 AM). See also the PeakWorkingSetSizeQuota key description above.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

StoreVideoFiles

>0

3

from 5.0

Time period for storage of not completely downloaded files on ATM-Intellect Pro. After the storage period is exceeded, the not completely downloaded files are deleted.


x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)


run_intellect


0.1


1


from 5.0

The key sets the ATM-Intellect Pro actions in case if the Intellect software is shut down.

0 – do not start the Intellect software

1 – start the Intellect software




x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)




socket_connect_tout




>=0




0




from 5.0

The key defines TCP/IP connection mode with ATM-Intellect Workstation.

0 – blocking mode. ATM-Intellect Pro connects to ATM-Intellect Workstation without specifying connection timeout.

>0 – non-blocking mode. ATM-Intellect Pro connects to ATM-Intellect Workstation with a connection timeout set by the socket_connect_tout > 0 parameter in seconds.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

write_buffer_enable

0.1

1

from 7.0

Data buffering while recording on disc when receiving video data on ATM-Intellect Workstation. ATM-Intellect Pro transfers video data to ATM-Intellect Workstation in packages of 800 to 4096 bytes (4096 by default). When buffering is enabled, a 264 Kb block of memory is allocated to the ATM-Intellect Workstation for receiving video data, and data is saved to the disk when this memory block is full, not every time a packet is received from ATM-Intellect Pro.

0 – buffering is enabled.

1 – buffering is disabled.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

stop_data_by_trx

0.1

1

from 5.0

The key determines the actions of ATM-Intellect Pro in case if, during the transfer of video data to ATM-Intellect ARM, a financial transaction has begun on the ATM.

0 – video data transfer is not stopped.

1 – video data transfer is suspended until financial transaction if completed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

IPPort> 07755from 5.0

The key specifies the port on the ATM-Intellect Workstation used for connecting the clients.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

financial_trx_tout

>0

60

from 7.0

Timeout for waiting for the financial transaction to complete in minutes. If after the start of the financial transaction during the time-out, there is no message from the ATM about its end, it will be considered to be completed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeAlarmFromAgent


0, 10from 10.0The key enables registration of the alarm with the time it occurred on the site.

0 – In the Alarm date field in the interface objects, the time of loading the alarm into the database after it is received from the Agent of Control is shown, not the time of occurrence of the alarm on site.

1 - In the Alarm date field in the interface objects, the time of alarm occurrence on site is shown.

Note. The key is set on the ATM-Intellect Workstation.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

FileQueryEnable0, 10from 10.0

The key enables automated video clip loading.

0 – automated video clip loading is disabled.

1 – automated video clip loading is enabled.

Note. The key is created at ATM-Intellect Workstation and/or Additional workplace.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

FileQueryPath
TextC:\Query\from 10.0

The key sets folder to share data with third party systems which is necessary for automated video clip loading.

Note. The key is created at ATM-Intellect Workstation and/or Additional workplace.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

OldLogPanel0, 10from 11.0

The key changes the Log Panel interface color theme.

0 - dark interface theme.

1 - light interface theme.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

StreamViewerExportPathText<Intellect installation directory>\exportfrom 11.0

The key specifies the path to the catalog of frames and video clips which were exported from the Monitoring interface during the live and archive video playback from a certain camera.

See Playing back live video and archive from a specific camera.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

MonitoringReserving0, 10from 11.0

The key removes the restriction on adding the same cameras for tracking in different Surveillance Objects.

0 - the restriction is enabled.

1 - the restriction is removed.

x32: HKLM\SOFTWARE\BitSoft\MonitorSSTV\Loader

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\MonitorSSTV\Loader

UseBulkInsert0, 1
from 10.0

The key accelerates the speed of data loading from files to the MonitorSSTV database by activating the group operator of data loading if the database is installed locally.

0 - do not use the BULK INSERT operator (if the SQL Server is remote)
1 - use the BULK INSERT operator (if the SQL Server is local)

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PrefixForTimeOutText-from 10.0The key specifies the prefix in the identifier of the Surveillance Objects for which the waiting timeout specified in the TimeoutForPrefix key should be specified.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeoutForPrefix>06from 10.0The key sets the waiting timeout in minutes for the ATM-Intellect Workstation to receive the packets with the technical state of ATM-Intellect Pro. After this time the "No connection" error will be displayed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

UsingTimeoutForPrefix0, 10only 10.0The key enables the waiting timeout set in the TimeoutForPrefix key for all Surveillance objects with the identifier prefix specified in the PrefixForTimeOut key.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PostfixForTimeOutText-from 11.0The key specifies the postfix in the identifier of the Surveillance Objects for which the waiting timeout specified in the TimeoutForPostfix key should be specified.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeoutForPostfix>06from 11.0The key sets the waiting timeout in minutes for the ATM-Intellect Workstation to receive the packets with the technical state of ATM-Intellect Pro. After this time the "No connection" error will be displayed.
HKEY_CURRENT_USER\SOFTWARE\BitSoft\MonitorSSTVMAXRECORDSONPAGE1,000 - 2,000,000,00010,000from 11.0Sets the maximum number of events to be displayed in the Event Log window without navigation buttons.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LastLoadThreshold >= 030from 11.0

The key sets the time in minutes, after which, if the data in the MonitorSSTV database is outdated, the corresponding indication on the ATM-Intellect Workstation will appear.

Restricting the Operator’s access to the camera's functional menu and its options

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_DISABLE_OPTION0, 10from 11.0

The key hides the camera's menu.

0 - The menu is displayed.

1 - The menu is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_ARM_DISABLE_OPTION0, 10from 11.0

The key hides the Arm menu option.

0 - The Arm menu option is displayed.

1 - The Arm menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_REC_DISABLE_OPTION0, 10from 11.0

The key hides the Start recording menu option.

0 - The Start recording menu option is displayed.

1 - The Start recording menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_CAMS_DISABLE_OPTION0, 10from 11.0

The key hides the Camera menu option.

0 - The Camera menu option is displayed.

1 - The Camera menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_TITLES_DISABLE_OPTION0, 10from 11.0

The key hides the Show titles menu option.

0 - The Show titles menu option is displayed.

1 - The Show titles menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_DISABLE_OPTION0, 10from 11.0

The key hides the Processing menu option.

0 - The Processing menu option is displayed.

1 - The Processing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_EXPORT_DISABLE_OPTION0, 10from 11.0

The key hides the Export menu option.

0 - The Export menu option is displayed.

1 - The Export menu option is hidden.

Restricting the Operator’s access to the Processing menu within the camera's functional menu

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_DEINTERLACE_DISABLE_OPTION0, 10from 11.0

The key hides the Deinterlacing menu option.

0 - The Deinterlacing menu option is displayed.

1 - The Deinterlacing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_ZOOM_DISABLE_OPTION0, 10from 11.0

The key hides the Zoom-in menu option.

0 - The Zoom-in menu option is displayed.

1 - The Zoom-in menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_CONTRAST_DISABLE_OPTION0, 10from 11.0

The key hides the Contrast menu option.

0 - The Contrast menu option is displayed.

1 - The Contrast menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_MASK_DISABLE_OPTION0, 10from 11.0

The key hides the Detector mask menu option.

0 - The Detector mask menu option is displayed.

1 - The Detector mask menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_SHARPNESS_DISABLE_OPTION0, 10from 11.0

The key hides the Sharpen menu option.

0 - The Sharpen menu option is displayed.

1 - The Sharpen menu option is hidden.

Restricting the Operator’s access to the CamMonitor component buttons

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_ARCH_DISABLE_OPTION0, 10from 11.0

The key hides the Archive button.

0 - The Archive button is displayed.

1 - The Archive button is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_TIME_DISABLE_OPTION0, 10from 11.0

The key hides the time.

0 - The time is displayed.

1 - The time is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_NAME_DISABLE_OPTION0, 10from 11.0

The key hides the camera name.

0 - The camera name is displayed.

1 - The camera name is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_MENU_DISABLE_OPTION0, 10from 11.0

The key hides the Menu button.

0 - The Menu button is displayed.

1 - The Menu button is hidden.

Restricting the Operator’s access to the CamMonitor control via the keyboard and mouse

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

KEYS_DISABLE_OPTION0, 10from 11.0

The key disables the control over the CamMonitor component using the hotkeys available for Video Monitor (see Video Monitor).

0 - The control over the CamMonitor component using the hotkeys is enabled.

1 - The control over the CamMonitor component using the hotkeys is disabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

TELEMETRY_ENABLE_OPTION0, 10from 11.0

The key enables the Telemetry control using the CamMonitor component (see Telemetry control).  

0 - The Telemetry control using the CamMonitor component is disabled

1 - The Telemetry control using the CamMonitor component is enabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

ARCH_DELETE_ENABLE_OPTION0, 10from 11.0

The key activates the Delete menu item which is used to remove the recordings from the archive. It is used only in Intellect version 4.11 and higher (see Deleting video recordings from the archive).

0 - The Delete item is hidden.

1 - The Delete item is displayed.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

ARCH_PROTECT_ENABLE_OPTION0, 10from 11.0

The key activates the Protect menu item which is used to protect the archive recordings from rewriting. It is used only in Intellect version 4.11 and higher (see Protection of separate record and disable of protection).

0 - The Protect item is hidden.

1 - The Protect item is displayed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

ExportPathText

DISK:\Export\

, where DISK is the drive on which the operating system is installed

-

Sets the path to the export directory on ATM-Intellect Workstation

 TABLE OF CONTENTS


ATM Event Capture

Registry section

String parameter

Available values

Default

Product version

Parameter in effect

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

JrnTOut

>0

10

от 9.0


Timeout in seconds for waiting for the information about the card insertion to appear in the ATM log after the actual card insertion.

For m_JrnMode=2 mode only (MAK3 TUSSON)

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

Mask>=0--

Specifies the options for masking the card number. By default, the first 6 and last 4 characters of the card number are not masked.

0 – if no mask to be applied to the card number.

1-6 – number of digits in the beginning of the card number which are not masked.

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

JrnMode>=00-

Specifies the key defines the mode of operating the journal.

0 – card number is read from the card reader

1 – card number is read from the ATM journal through the Protopas software (Wincor)

2 – card number is read from the ATM journal through the MAK3 (TUSSON) software

3 – card number is read from the ATM journal through the TellMe (SCS) software

4 – card number is read from the ATM journal through the APTRA Advance NDC (NCR) software

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

JrnPath >=0--

Specifies the path to the ATM’s journal.

If JrnMode = 1, then JrnPath = C:\JOURNAL\

If JrnMode = 2, then JrnPath = C:\scs\atm_h\PRJ\

If JrnMode = 3, then JrnPath = C:\scs\atm_h\PRJ\

If JrnMode = 4, then JrnPath = C:\program files\ncr aptra\advance ndc\data\

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

JrnTrack2Substring >=0--

Specifies substring for searching the card number.

If JrnMode = 1, then JrnTrack2Substring = (TRACK 2 DATA):

If JrnMode = 2, then JrnTrack2Substring = @++

If JrnMode = 3, then JrnTrack2Substring = CARD:

If JrnMode = 4, then JrnTrack2Substring = CARD:

x32: (x32-ATM Event Capture)

x64: (x64-ATM Event Capture)

LogEnable0, 10-

Enables logging in ATM Event Capture utility

0 - event log is disabled

1 - event log is enabled. After you quit and start ATM Event Capture utility again, the file EventATM.log appears in the installation folder.

...

Monitoring

Registry section

String parameter

Available values

Default

Product version

Description

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LPRDBsearchresultUnicodeBase64

0, 1

1

8.0

The key sets how to process message in param0<> for the SEARCH_RESULT event of the LPRDB ("External database") object – as ANSI line or Unicode line additionally encoded in base64.

0 – ANSI

1 – UnicodeBase64


x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PeakWorkingSetSizeQuota

>=0

100

from 8.0


The maximum memory size in megabytes used by the process videosrv.exe on  Agent of Control. If the parameter is set to 0, then the check for the used memory is not performed.

Once a day, the  Agent of Controlchecks the size of the memory it uses. The check is performed at the time specified by the TimeOfCheckWorkingSetSize key (see below).

After exceeding the specified value, the videosrv.exe module is rebooted.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeOfCheckWorkingSetSize

>=0

3

from 8.0

Time to check memory usage in hours. Default value is 3 (3:00 AM). See also the PeakWorkingSetSizeQuota key description above.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

StoreVideoFiles

>0

3

from 5.0

Time period for storage of not completely downloaded files on  Agent of Control. After the storage period is exceeded, the not completely downloaded files are deleted.


x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)


run_intellect


0.1


1

from 5.0

The key sets the  Agent of Control actions in case if the Intellect software is shut down.

0 – do not start the Intellect software

1 – start the Intellect software




x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)




socket_connect_tout




>=0




0

from 5.0

The key defines TCP/IP connection mode with  Server of Control.

0 – blocking mode.  Agent of Control connects to  Server of Control without specifying connection timeout.

>0 – non-blocking mode.  Agent of Control connects to  Server of Control with a connection timeout set by the socket_connect_tout > 0 parameter in seconds.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

write_buffer_enable

0.1

1

from 7.0

Data buffering while recording on disc when receiving video data on  Server of Control.  Agent of Control transfers video data to  Server of Control in packages of 800 to 4096 bytes (4096 by default). When buffering is enabled, a 264 Kb block of memory is allocated to the  Server of Control for receiving video data, and data is saved to the disk when this memory block is full, not every time a packet is received from  Agent of Control.

0 – buffering is enabled.

1 – buffering is disabled.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

stop_data_by_trx

0.1

1

from 5.0

The key determines the actions of  Agent of Control in case if, during the transfer of video data to ATM-Intellect ARM, a financial transaction has begun on the ATM.

0 – video data transfer is not stopped.

1 – video data transfer is suspended until financial transaction if completed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

IPPort> 07755from 5.0

The key specifies the port on the Server of Control/Central Server of Control used for connecting the clients.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

financial_trx_tout

>0

60

from 7.0

Timeout for waiting for the financial transaction to complete in minutes. If after the start of the financial transaction during the time-out, there is no message from the ATM about its end, it will be considered to be completed.

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

ULPRspecialProcessing>=0-from 10.0

The key enables special operation mode of the Monitoring software joint with Auto Intellect.

1 – the special operation mode of the Monitoring software joint with Auto Intellect is enabled.

Any other value – the special operation mode is disabled.

Note. The key is created both on Agent of Control and Server of Control.

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

PlaceOfRecognitionN1,2-from 10.0

This parameter corresponds to the point of recognition. PlaceOfRecognitionN, where N is the ID of the LPR channel object.

1 – entrance.

2 – exit.

Note 1. The key is in use in special operation mode of the Monitoring software joint with Auto Intellect.

Note 2. The key is created at Agent of Control

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

CamOfRecognitionN>0-from 10.0

This parameter corresponds to the ID of a camera added to the recognition module. CamOfRecognitionN, where N is the ID of the LPR channel object. 

The value of this parameter corresponds to the Camera object ID specified in the LPR channel object settings.

Note 1. The key is in use in special operation mode of the Monitoring software joint with Auto Intellect.

Note 2. The key is created at Agent of Control

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

AlarmMsgOne>=0-from 10.0

The key enables the LP found in the database alarm both for Entrance and Exit recognition points.

0 – enables the LP found in the database alarm both for Entrance and Exit recognition points.

Any other value – the LP found in the database alarm is generated for Entrance recognition point only.

Note 1. The key is in use in special operation mode of the Monitoring software joint with Auto Intellect.

Note 2. The key is created at Server of Control

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeAlarmFromAgent0, 10from 10.0

The key enables registration of the alarm with the time it occurred on the site.

0 – In the Alarm date field in the interface objects, the time of loading the alarm into the database after it is received from the Agent of Control is shown, not the time of occurrence of the alarm on site.

1 - In the Alarm date field in the interface objects, the time of alarm occurrence on site is shown.

Note. The key is set on the Server of Control.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

FileQueryEnable   


0, 10from 10.0

The key enables automated video clip loading.

0 – automated video clip loading is disabled.

1 – automated video clip loading is enabled.

Note. The key is created at Server of Control and/or Additional workplace.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

FileQueryPath


TextC:\Query\from 10.0

The key sets folder to share data with third party systems which is necessary for automated video clip loading.

Note. The key is created at Server of Control and/or Additional workplace.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

OldLogPanel0, 10from 11.0

The key changes the Log Panel interface color theme.

0 - dark interface theme.

1 - light interface theme.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

StreamViewerExportPathText<Intellect installation directory>\exportfrom 11.0

The key specifies the path to the catalog of frames and video clips which were exported from the Monitoring interface during the live and archive video playback from a certain camera.

See Playing back live video and archive from a specific camera.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

MonitoringReserving0, 10from 11.0

The key removes the restriction on adding the same cameras for tracking in different Partitions of Control.

0 - the restriction is enabled.

1 - the restriction is removed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

AccessByCardEnable0, 10from 11.0

The key activates the special  mode of Monitoring operation together with ACFA-Intellect, as well as the ability to customize the long alarm description.

0 - Special operation mode is off.

1 - Special operation mode is on.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

CustomisedLongAlarmNameTextObject disarmedfrom 11.0

The key changes the description of the long alarm Object disarmed in the Monitoring and Monitoring reports interface objects.

x32: HKLM\SOFTWARE\BitSoft\MonitorSSTV\Loader

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\MonitorSSTV\Loader

UseBulkInsert0, 1
from 10.0

The key accelerates the speed of data loading from files to the MonitorSSTV database by activating the group operator of data loading if the database is installed locally.

0 - do not use the BULK INSERT operator (if the SQL Server is remote)
1 - use the BULK INSERT operator (if the SQL Server is local)

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PrefixForTimeOutText-only 10.0The key specifies the prefix in the identifier of the Partitions of Control for which the waiting timeout specified in the TimeoutForPrefix key should be specified.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeoutForPrefix>06only 10.0The key sets the waiting timeout in minutes for the Server of Control to receive the packets with the technical state of Agent of Control. After this time the "No connection" error will be displayed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

UsingTimeoutForPrefix0, 10only 10.0The key enables the waiting timeout set in the TimeoutForPrefix key for all Partitions of Control with the identifier prefix specified in the PrefixForTimeOut key.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PostfixForTimeOutText-from 11.0The key specifies the postfix in the identifier of the Partitions of Control for which the waiting timeout specified in the TimeoutForPostfix key should be specified.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

TimeoutForPostfix>06from 11.0The key sets the waiting timeout in minutes for the Server of Control to receive the packets with the technical state of Agent of Control. After this time the "No connection" error will be displayed.
HKEY_CURRENT_USER\SOFTWARE\BitSoft\MonitorSSTVMAXRECORDSONPAGE1,000 - 2,000,000,00010,000from 11.0Sets the maximum number of events to be displayed in the Event Log window without navigation buttons.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PassiveModeForFTP 0, 11from 11.0

The key sets the operation mode of the Central Server of Control software via FTP.

0 - Active mode.

1- Passive mode.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

PeriodRequestOfStatistic> 05from 11.0

The key sets the statistics polling period in minutes for the Servers of Control.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LogArchPeriod> 0168from 11.0

The key sets the log archiving period in hours of the Communication module (CentralNetServer.log)

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LogMaxSize> 0100from 11.0

The key sets the maximum size of the communication module log file at which it begins to archive ignoring the LogArchPeriod parameter.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LogArchDelPeriod> 03from 11.0

The key sets the log files archive retention period in months (CentralNetServer.log).

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

KeepDB> 06from 11.0

The key sets the data retention period of closed errors and alarms in the Server SSTV DB.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

LastLoadThreshold >= 030from 11.0

The key sets the time in minutes, after which, if the data in the MonitorSSTV database is outdated, the corresponding indication on the Server Of Control/CSC will appear.

Restricting the Operator’s access to the camera's functional menu and its options

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_DISABLE_OPTION0, 10from 11.0

The key hides the camera's menu.

0 - The menu is displayed.

1 - The menu is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_ARM_DISABLE_OPTION0, 10from 11.0

The key hides the Arm menu option.

0 - The Arm menu option is displayed.

1 - The Arm menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_REC_DISABLE_OPTION0, 10from 11.0

The key hides the Start recording menu option.

0 - The Start recording menu option is displayed.

1 - The Start recording menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_CAMS_DISABLE_OPTION0, 10from 11.0

The key hides the Camera menu option.

0 - The Camera menu option is displayed.

1 - The Camera menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_TITLES_DISABLE_OPTION0, 10from 11.0

The key hides the Show titles menu option.

0 - The Show titles menu option is displayed.

1 - The Show titles menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_DISABLE_OPTION0, 10from 11.0

The key hides the Processing menu option.

0 - The Processing menu option is displayed.

1 - The Processing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_EXPORT_DISABLE_OPTION0, 10from 11.0

The key hides the Export menu option.

0 - The Export menu option is displayed.

1 - The Export menu option is hidden.

Restricting the Operator’s access to the Processing menu within the camera's functional menu

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_DEINTERLACE_DISABLE_OPTION0, 10from 11.0

The key hides the Deinterlacing menu option.

0 - The Deinterlacing menu option is displayed.

1 - The Deinterlacing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_ZOOM_DISABLE_OPTION0, 10from 11.0

The key hides the Zoom-in menu option.

0 - The Zoom-in menu option is displayed.

1 - The Zoom-in menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_CONTRAST_DISABLE_OPTION0, 10from 11.0

The key hides the Contrast menu option.

0 - The Contrast menu option is displayed.

1 - The Contrast menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_MASK_DISABLE_OPTION0, 10from 11.0

The key hides the Detector mask menu option.

0 - The Detector mask menu option is displayed.

1 - The Detector mask menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

MENU_PROCESSING_SHARPNESS_DISABLE_OPTION0, 10from 11.0

The key hides the Sharpen menu option.

0 - The Sharpen menu option is displayed.

1 - The Sharpen menu option is hidden.

Restricting the Operator’s access to the CamMonitor component buttons

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_ARCH_DISABLE_OPTION0, 10from 11.0

The key hides the Archive button.

0 - The Archive button is displayed.

1 - The Archive button is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_TIME_DISABLE_OPTION0, 10from 11.0

The key hides the time.

0 - The time is displayed.

1 - The time is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_NAME_DISABLE_OPTION0, 10from 11.0

The key hides the camera name.

0 - The camera name is displayed.

1 - The camera name is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

BUTTON_MENU_DISABLE_OPTION0, 10from 11.0

The key hides the Menu button.

0 - The Menu button is displayed.

1 - The Menu button is hidden.

Restricting the Operator’s access to the CamMonitor control via the keyboard and mouse

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

KEYS_DISABLE_OPTION0, 10from 11.0

The key disables the control over the CamMonitor component using the hotkeys available for Video Monitor (see Video Monitor).

0 - The control over the CamMonitor component using the hotkeys is enabled.

1 - The control over the CamMonitor component using the hotkeys is disabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

TELEMETRY_ENABLE_OPTION0, 10from 11.0

The key enables the Telemetry control using the CamMonitor component (see Telemetry control).  

0 - The Telemetry control using the CamMonitor component is disabled

1 - The Telemetry control using the CamMonitor component is enabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

ARCH_DELETE_ENABLE_OPTION0, 10from 11.0

The key activates the Delete menu item which is used to remove the recordings from the archive. It is used only in Intellect version 4.11 and higher (see Deleting video recordings from the archive).

0 - The Delete item is hidden.

1 - The Delete item is displayed.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

ARCH_PROTECT_ENABLE_OPTION0, 10from 11.0

The key activates the Protect menu item which is used to protect the archive recordings from rewriting. It is used only in Intellect version 4.11 and higher (see Protection of separate record and disable of protection).

0 - The Protect item is hidden.

1 - The Protect item is displayed.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

RequestFullStatisticOnStartup 
0, 10from 12.0

By default, the Central Server of Control requests a complete package of statistics from all Servers of Control only once, when it first connects to the Servers of Control.

The key activates the request on the Central Server of Control for a complete statistics package from all Servers of Control every time the CentralNetServer.exe communication module is launched.

0 - disabled.

1 - a complete statistics package will be requested from all Servers of Control each time the CentralNetServer.exe communication module is launched.

Attention! Requesting a complete statistics package is a resource-intensive operation. It is only necessary to activate this key if absolutely necessary.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

RequestFullStatistic[N]

Note. [N] is the internal identifier of the Server of Control object in Intellect

0, 10from 12.0

By default, the Central Server of Control requests a complete package of statistics from all Servers of Control only once, when it first connects to the Servers of Control.

The key activates the request for a complete statistics package from a specific Server of Control once. The request will be executed when the CentralNetServer.exe communication module is launched, and the value of this key will automatically change to 0.

0 - disabled.

1 - a complete statistics package from a specific Server of Control will be requested once when the CentralNetServer.exe communication module is launched.

Attention! Requesting a complete statistics package is a resource-intensive operation. It is only necessary to activate this key if absolutely necessary.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

FtpPathText<Intellect installation directory>\Vhost\DATA\FTP\from 13.0

Sets the path to the FTP directory on the Server of Control for working with the Central Server of Control.

x32: (x32-ATM/Monitoring)

x64: (x64-ATM/Monitoring)

ExportPathText

DISK:\Export\

, where DISK is the drive on which the operating system is installed

-Sets the path to the export directory on the Server of Control

 TABLE OF CONTENTS


IP integration (drivers and codecs pack for Intellect)

Registry section

String parameter

Available values

Default

Product version

Parameter in effect

x32: (X32)\Video
x64: (x64)\Video

ArchiveFps

1-24


4.7.5 and later

Sets the number of frames recorded to the archive (max.resolution). LiveFps and ArchiveFps parameters are not to exceed 24 in total.

x32: (X32)\Video
x64: (x64)\Video

ArecontVision

0, 1


up to  4.8.0

Enables the protocol for integrating Arecont cameras. The key is not in use.

x32: (X32)\Video
x64: (x64)\Video

DoubleStream

0, 1


4.7.5 and later

Defines whether asynchronous video display mode is enabled or not.

x32: (X32)\Video
x64: (x64)\Video

IpIntDrivers3

Brand name: Axis; Acti, etc.


4.7.3 and later

The IpIntDrivers3 string parameter is created and the names of brands that need 3.0 driver are listed.

x32: (X32)\Video
x64: (x64)\Video

IpIntDriverVersion

2, 3


4.7.3 and later

Defines the version number of loaded drivers:
2 – to load drivers version 2.0;
3 - to load drivers version 3.0;
This parameter has a high priority and cancels IpIntDrivers3 parameter.

x32: (X32)\Video
x64: (x64)\Video

LiveFps

1-24


4.7.5 and later

Sets the number of frames displayed in the 800x600 format. LiveFps and ArchiveFps parameters are not to exceed 24 in total.

x32: (X32)
x64: (x64)

LoadIpIntDirectly

0, 1

 

4.9.0 and later 

1 - enable IntegratedDevice via video.run. If the setting is enabled and at least one IntegratedDevice is added, then other IP video capture cards are disabled.

0 - IIntegratedDevice operates as a separate run-module.

x32: (X32)\Video\TransportProtocols
x64: (x64)\Video\TransportProtocols		<Driver name><protocol>-DP 3.1.1 and later

The key is used to change a transport protocol used by the IP device.

Example of the key value: "ONVIF"="tcp" means that TCP protocol is used to transfer data via ONVIF.

See details in Changing the transport protocol used by IP-device

Example of the key value: "rtsp"="multicast" allows enabling Multicast mode of the RTSP Server. The object configuration is required in addition to the key.

See details in Configuring RTSP Server module.

x32: (X32)\Video\MetadataTransportProtocols
x64: (x64)\Video\MetadataTransportProtocols

The name of camera driver (in the driver parameter of the

C:\Program Files\ Common Files\ AxxonSoft\ Ipint.DriverPack \3.0.0\ Ipint.<Driver name>.rep file)		The name of transport protocol (is to be the same as one of the values specified in metadataTransportProtocol property in the corresponding .rep file).-DP 3.31.1613 and laterThe key is used to change a metadata transport protocol. At the time of writing this documentation change of a metadata transport protocol was available for ONVIF driver only (possible values are tcp and udp).
x32: (X32)\Video
x64: (x64)\Video		UnloadUnusedDriverTimeout>=060DP 3.32.1638 and later

The key sets unused driver unload timeout for cameras. For instance, if camera brand is in several drivers, all of them are loaded at camera connection. To unload the unused drivers, set non-zero value to this key.

If the key is not created, then unused drivers are unloaded in 60 seconds.

0 – drivers do not unload (such behavior was in DriverPack versions older than the current one).

The key value that is > 0 sets unused driver unload timeout.

If the key is created but it consists of NaN value, then unused driver unload timeout is set to the default value – 60 seconds.

x32: (X32)\TELEMETRY
x64: (x64)\TELEMETRY

PresetCompatibility0, 1-DP 3.43.1950 and later

The key is used to enable the compatibility between presets in Intellect and previous versions of Drivers Pack, i.e. to decreasing the preset number by 1 when sending it to the driver.

0 – a new operation mechanism with presets the same as in AxxonNext is in use in Intellect. If preset 1 is selected in Intellect interface, then value 1 is sent to the driver.

1, or if the key is not created – the compatibility mode is in use: if preset 1 is selected/created in Intellect interface, then value 0 is sent to the driver.

x32: (x32)\Video
x64: (x64)\Video

FFTHREADCOUNT>=01DP 3.43.1955 and later

The key sets the number of streams created in FFmpegDecoder.

0 – decoder automatically selects the number of created streams.

>0 – sets the number of streams in use.

By default if there is no key or the value is incorrect, then value 1 is in use.

Auto selection of the number of streams can result in the system load reduction or its increase as the number of streams recreated during decoding increases – this affects the performance.

x32: (x32)\EventSources
x64: (x64)\EventSources

<brand>.<model> (for example, ONVIF.1_channel_device).

If all models of some manufacturer require a specific method of getting events, then there must be a string key named <brand> in the section.

Pull point

Meta data

Disable

Meta dataDP 3.35.1692

By the date the documentation in created, this key is supported for three brands: ONVIF, RVi and IDIS. For models of these brands, the key is created automatically when the Drivers Pack is installed.

The key sets a method of getting data about the analytics and the sensors of the device:

  • Pull point – getting events by http request of the camera
  • Meta data – getting events from the metadata stream
  • Disable – getting events is disabled.
All other values (including an empty string) or if there is no key for the model and brand in the specified section mean that you must use the default method, created as default in the rep file for the given model.
x32: (x32)\Video\UseSsrcChecking
x64: (x64)\Video\UseSsrcChecking		RTSP

enable

disable

enableDP 3.45.2055

The key is intended for setting up synchronization source (SSRC) for RTSP stream:

enable – SSRC check enabled;

disable – SSRC check disabled.

x32: (x32)\Video
x64: (x64)\Video

FFLOGDELAY0, 10CP 1.580Enables logging of delays of frames decoding and idle time for FFMPEG codec.
x32: (x32)\Video\TsConverters
x64: (x64)\Video\TsConverters

<brand>.<model>, for example, Tattile.ANPR Mobile

If all brand's models require a certain method of the timestamp adjustment, then the section must contain a string key with the name <brand>.

  • InfrequentTs
  • ValidDeviceTs
  • None
Depends on the brandDP 3.34 and later

The keys in this section specify the method of the frame timestamp adjustment.

If the key is not created, the timestamp transferred to the Intellect equals 0, and then the current time is set as its value.

The None value is used if it is necessary to disable the adjustment and transfer the timestamp received from the camera as is.

The ValidDeviceTs value means that the timestamp adjustment method is used before the timestamps transmission to the Intellect if the timestamp received from the camera differs from the current time by the value greater than the one specified in the MaxTimestampDeviation key (see below). After the adjustment, the timestamp calculated on the basis of the previous frame's timestamp and the time elapsed since its reception is transmitted to the Intellect.

InfrequentTs value discards the relative timestamps, transferring 0 to the Intellect instead (i.e., the current time is set as the timestamp value), and it also transfers the absolute timestamps with the ETimestampValidityFlag flag. This adjustment method should be used for the devices with the license plates recognition which transfer the separate frames to the external system, rather than a continuous video stream.

For some manufacturers, when installing the Drivers Pack, the keys with the necessary values are automatically created in the appropriate registry key.

x32: (x32)\Video
x64: (x64)\Video		MaxTimestampDeviation>=0-DP 3.34 and later

The key is used for the ValidDeviceTs key value from the TsConverters branch (see above).

The key sets the maximum permissible deviation of the frame timestamp from the current Server time.

x32: (x32)\Video
x64: (x64)\Video		ErrorSensitivity0, 10DP 3.54 and later

The key enables the interruption of the H.265 video decoding via the ffmpeg decoder in case of the slightest error in the video stream.

0 - if the video stream contains errors, then a buffer with artifacts will be received from the ffmpeg decoder.

1 - if the video stream contains errors, then an empty buffer will be received from the ffmpeg decoder.

x32: (x32)\Video\RTSP
x64: (x64)\Video\RTSP		AudioSeparatedConnection0, 10DP 3.60 and laterEnables RTSP audio over a separate TCP connection.
x32: (x32)\Video
x64: (x64)\Video		servicesVersionauto, ver1, ver2autoDP 3.61 and later

The key sets the version of ONVIF services (only for ONVIF and ONVIF 2.X):

auto – get available versions and choose the latest if possible.

ver1 – use old versions of services.

ver2 – use new versions of services.

x32: (x32)\Video
x64: (x64)\Video		servicesSourcegetServices, getCapabilitiesgetServicesDP 3.61 and later

The key determines the source of the ONVIF services version (only for ONVIF and ONVIF 2.X):

getServices – get a list of services using the new interface.

getCapabilities – get a list of services using the old interface.

x32: (x32)\Video\Virtual
x64: (x64)\Video\Virtual		​playFileOnce0, 10from DP 3.62

Disables looping files in a virtual video capture device of a Virtual bench type.

0 - videos in a Virtual bench virtual capture device are played in a loop.

1 - videos in a Virtual bench virtual capture device are played once.

See also Creating and configuring a virtual Video Capture Device.

x32: (X32)\TELEMETRY
x64: (x64)\TELEMETRY		cgiPrefix

"/cgi-bin/ptz.cgi?", "/stw-cgi/ptzcontrol.cgi?"

-DP 3.58 and later

The key is required for PTZ operation with Hanwha Techwin IP-devices:

"/cgi-bin/ptz.cgi?" – for old models (not X-series)

"/stw-cgi/ptzcontrol.cgi?" –  for new models X-series

...