Page History

The ZK C3-100, ZK C3-200, ZK C3-400 controllers are configured You can configure the ZK Teco C3, C5, InBio controllers on the settings panel of the corresponding objects AC ZK Controller C3 -100controller,  AC ZK Controller C3-200 and AC ZK Controller C3-400 which ZK C5 controller and ZK INBIO controller objects that are created on the basis of the AC ZK Teco object on the Hardware tab of the System settings dialog window parent object.

To configure the a ZK Teco controllers controller, do the following:

1. Go to the settings panel of the corresponding corresponding ZK Teco controller..
   Image Modified
2. From the Gate drop Interlock drop-down list (1), select the type of controller connection (see Configuring the connection to the ZK Teco controller/elevator control panel or Configuring the connection via RS-485 standard).
3. In the Password field (2), enter the password for controller connection.
4. If the Ethernet connection type was selected, then enter the IP address of the controller in the IP field (3).
5. If the the RS-485 standard connection type was selected, then select the connection COM port number from the Address drop-down list (3).
6. a group of interlocked doors. Interlock is a two-cycle mode with a stop to check a person who enters. Interlock can be set for two or more locks belonging to one access controller.
   Image Added
   1. Disable—doors interlock function is disabled (default).
   2. Doors 1 and 2—doors 1 and 2 are interlocked.
   3. Doors 3 and 4—doors 3 and 4 are interlocked.
   4. Doors 1, 2 and 4—door 1, door 2 is interlocked with door 4.

   From the Anti-passback drop-down list (4), select the mode of anti-passback operation:

   Mode

   Description

   Controller

   Disable

   The anti-passback function is disabledAll controllersReaders of Door 1The anti-passback function is enabled between the readers of Door 1ZK C3-100, ZK C3-200Readers of Door 2The anti-passback function is enabled between the readers of Door 2ZK C3-200Readers of door 1, readers of door 2The anti-passback function is enabled between the readers of Door 1 and Door 2 respectivelyZK C3-200Door 1 and 2The anti-passback function is enabled between the readers of Door 1 and Door 2ZK C3-200, ZK C3-400Doors 3 and 4The anti-passback function is enabled between the readers of Door 3 and Door 4ZK C3-400Doors 1 and 2, doors 3 and 4The anti-passback function is enabled between the readers of Door 1, Door 2, Door 3 and Door 4ZK C3-400

   Doors 1, 2 and doors 3, 4

   The anti-passback is enabled between Door 1, 2 and Door 3, 4ZK C3-400Door 1 and doors 2, 3The anti-passback is enabled between Door 1 and Door 2, 3ZK C3-400Door 1 and doors 2, 3, 4 The anti-passback is enabled between Door 1 and Door 2, 3, 4ZK C3-400

   From the Interlock drop-down list (5), select the mode of doors interlocking:

   Mode

   Description

   Controller

   Disable

   The interlock function is disabledAll controllersDoor 1 and 2Doors 1 and 2 are interlocked mutuallyZK C3-200, ZK C3-400Door 3 and 4Door 3 and door 4 are interlocked mutuallyZK C3-400Doors 1, 2 and 4Door 1, door 2 and door 4 are interlocked mutuallyZK C3-400
   2. Doors 1 and 2, doors 3 and 4
   Door 1 and
   1. —door 1 is interlocked with door 2
   are interlocked mutually
   1. ,
    door
   1. door 3
   and ZK C3-400
   1. is interlocked with door 4
   are interlocked mutually
   1. .
   Door
   1. Doors 1, 2, 3 and 4
   1. —door 1, door 2, door 3
   and
   1. is interlocked with door 4
   are interlocked mutuallyZK C3-400
   1. .
      

      Info
      title Note
      To open one of the

   interconnected

   1. interlocked doors,

   the

   1. other

   interconnected

   1. interlocked doors in the group must

   remain

   1. be closed. This means that only one door in a group of

   interconnected

   1. interlocked doors

   , only one door

   1. can be opened at a time.

      
      
7. From the Backup Reserv. period drop drop-down list (6), in the range from 1 to 24, select the time interval period in minutes for after which the automatic backup of data of the specified type (see Managing the configuration of ZK Teco controllers). Set the Watch dog checkbox (7) to enable the automatic data backupdata will be automatically backed up. The default value is 1.

8. The Watchdog checkbox is set by default. It enables the watchdog timer. This is a monitoring system that restarts the hardware in time to restore its functionality if a failure occurs. If the microcontroller port does not respond to the timer within a certain time or number of cycles determined in the program, a reset and restart command is sent to the device. To disable the mode, clear the checkbox.

9. Set the Two doors two directions mode checkbox to enable two-directional access control for two doors.

10. From the Mode number drop-down list, select the antipassback control mode. By default, this setting is disabled (Disabled). The antipassback control modes depend on the controller type (For details, see the manufacturer's documentation).

11. Click the Apply button (9).

    Info
    title Note.
    After a successful connection with the controller is established, the firmware version and the controller serial number general information about the device will automatically be displayed in area (8).

...

1. the corresponding area on the left side of the settings panel.