Page History

If you are using use a fisheye camera or video camera with a panomorph lens, configure do the following settings of the Video camera object, in the Panomorph settings group::

1. Select the Camera object in the Hardware tab (see Camera).
2. Set the value in the Panomorph view parameter group:

   Parameter	Value	Description
   Panomorph view
   Activate	Yes	By default, panomorph view is disabled. To enable it, select the yes value
   	No
   Camera position	Wall	Select camera position

3. To activate panoramic view, in the Activate list (1), select Yes.
   Image Removed
In the Camera position list(2), select the mount of the video camera.

4. Note title Attention! Some

system features and functions

5. functions and features of the system depend on the

chosen position of the video camera

6. selected camera position: digital

zoom

7. video zooming, display of video in the surveillance sector on the map, and

immersive

8. immersion mode.
   	Ceiling
   	Floor
   Lens type	Common fisheye-lens	If it is a fisheye camera, select the Common fisheye-lens

lens type (3). If it is a video camera with a panomorph

9. lens

, select the corresponding

10. type

. When using wide angle dual lens XingYun devices, select the Double sphere fisheye-lens type.

11. Info title Note The types of device lenses certified by ImmerVision are listed in the document. You cannot select ImmerVision lenses in Linux.
    Double sphere fisheye-lens	When using wide angle dual lens XingYun devices, select the Double sphere fisheye-lens type.
    A0**V	If it is a video camera with a panomorph lens, select the corresponding type. In this case, you must perform the calibration of the video image. To do this, select the yes value.
    A1UST
    A8TRT
    B0QQV
    B4QQV
    B5SST
    B6SST
    B72YV
    B8QQT
    B9VVT
    C1ZZV
    C2TTV
    C322V
    C4VVV
    C7SST
    C8WWT
    C9VVT
    D1SST
    D2WWV
    D4SST
    D9SSV
    E3VVV
    View type	PTZ	If you use a camera with an Immervision lens, select the appropriate display mode (4): 360о panorama with virtual PTZ (PTZ value) or 180о panorama (Perimeter).
    	Perimeter
    Fit to frame	Yes	By default, the parameter is disabled. A typical fisheye lens with standard settings produces a skewed image in the upper part of the screen.

If this is the case, enable the Fit to frame option (5)

12. As a result, the video image is automatically calibrated and cut at the edges of the frame, which can result in a significant loss of frame area. Note title Attention! If

you have

13. there are multiple streams from a camera, you

need to

14. must calibrate each stream. To do this, before applying the settings, switch

to

15. the

required

16. stream tab in the Surveillance window (see Camera).

Notetitle
Attention!

18. Video is calibrated every time you change any parameters in the Panomorph group.

Manual calibration is also available. To do this:

Disable
1. In the Fit to frame field, select the No value from the drop-down list.
2. In the Activate field, select the No
in the Enable list and click
3. value from the drop-down list.
4. Click the Apply button.
Select Yes in the Enable
5. In the Activate field, select the Yes value from the drop-down list.
6. Configure the circle video area
(circle). Left
7. . To move the circle, left-click any point inside the circle and move the mouse pointer. To change the diameter of the circle,
do as follows:
8. click an anchor
point
9. point Image Modified and move the mouse pointer.
   Image Modified
10. Click the Apply button button.
    After applying the settings, the area outside the circle will be cut.

Configuration of the fisheye camera is complete.