Page History

The settings panel of the SIP-device system object is shown in the figures below.

Image Removed

Table describes the setting parameters of the SIP-device system object.

The description of the settings parameters is given in the tables.

Image Added

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	Identification number*	Automatically	Displays the identification number of the SIP-device object system object in the system	Numbers, letters, periods, hyphen, dash, and underscore	-NA	Depends on the number of the SIP-device objects in the system the video surveillance system with distributed architecture
2	Name*	Enter the value into in the field	Sets a name of the SIP-device object in the video surveillance system with distributed architecture	Latin, Cyrillic, and service characters	SIP-terminal	A line containing a sequence of any characters (letters, digits, service characters except > and < characters), case-insensitive. Number of characters—from 1 to 60
3	Disable	Set the checkbox	Sets the state (enabled or disabled) of theDisables the SIP-device object in the video surveillance system with distributed architecture	Boolean type	Clear	Set—the SIP-device object is disabled and isn't used Clear—Clear—the SIP-device object is enabled and used
4	SIP-terminal	Select the value from the list	Sets the SIP-terminal parent object for the given SIP-device object	Name of the SIP-terminal objects registered in the system	Name of the SIP-terminal parent object	Depends on the number of the SIP-terminal objects in the system
5	Device type	Select the value from the list	Sets the icon type to display the device on the Map	Names of the available icon types	-	NA	Empty line (no value); No value touch panel; speaker; camera; microphone; default
6	Device priority	Select the value from the list	Sets the priority of a call from this device in the incoming calls window of the SIP panel	Sequence of numbers	-	NA	From 1 to 10.0–10 The lower the number, the higher the priority and, accordingly, the higher the display in the list . ; If the field is left blank, then the priority is considered to be minimal . ; Calls from devices with the same priority will be are sorted by the time of the call
The Device connection settings group
7	User ID	Enter the value into in the field	Sets the SIP-device identification number, i.e. that is, the number to call it	Sequence of numbers	NA	>=0
	Device IP address	Enter the value into in the field	For the SIP-server terminal type only. Sets the SIP-device IP address	IP address	NA	1.0.0.0–2550—255.255.255.255
	Password	Enter the value into in the field	For the SIP-server terminal type only. The password specified on the SIP-device	Latin, Cyrillic, and service characters	NA	A line containing a sequence of any characters (letters, digits, service characters)
	State	Automatically	For the SIP-server terminal type only. Displays the SIP-device state -	NA	NA	-	-	NA

*Name of the element isn't displayed in the settings panel of the given object.

The The Video/Audio tab (only for the SIP-server terminal type).

Image Modified

Table describes the setting parameters of the Video / Audio tab.

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	Video	Set the switch to the required radio buttonposition	Sets the video camera used for calls	Supported options of camera usage	Off	Off—the video is not isn't used during the call; SIP camera—a SIP-device camera connected via the SIP protocol is used; Other—any other camera from the Axxon PSIM hardware tree selected from the Camera drop-down list is used
2	Camera	Select the value from the list	Sets any video camera used for calls	Name of the Camera objects registered in the system	-NA	Depends on the number of the Camers objects in the system
3	Audio	Set the switch to the required radio buttonposition	Enables or disables the audio during a call	Supported options of audio usage	Off	Off—the audio is not isn't used during the call On—the microphone of the SIP-device is used during the call
4	Microphone	Automatically	Displays the name of the Microphone object corresponding to the SIP-device-	NA	-NA-	NA

The Relay tab (only for the SIP-server terminal type).

Image Modified

Table describes the setting parameters of the Relay tab.

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	DTMF type	Select the value from the list	Sets the type of the tone

DTMF

signal	Supported signal types	sip_info	sip_info—signals are transmitted in the INFO message of the SIP protocol; sip_notify—signals are transmitted in the NOTIFY message of the SIP protocol; in_band—the signal is transmitted as normal sound in an audio stream; http_bas—signals are transmitted via the HTTP protocol separately from the voice stream
2	Signal duration, ms	Enter the value

into

in the field

Sets the time period in milliseconds during which the DTMF signal

should

must be sent	Sequence of numbers	NA	>0
3	Device connection settings

-

NA

Opens

a

the Device connection settings pop-up window

of connection settings

only when the http_bas type of tone is selected

-

NA	Inactive by default

-

NA
4	Name	Enter the value

into

in the field	Sets the name of the command that will be displayed on the SIP-panel	Latin, Cyrillic, and service characters	NA	A line containing a sequence of any characters (letters, digits, service characters)
5	Code	Enter the value

into

in the field

Sets the unique command code

Sequence of numbers or HTTP request (for http_bas)

NA

A line containing a sequence of numbers or HTTP request

The Device connection settings pop-up window.

Image Removed

Table table below describes the fields of the Device connection settings window.

Image Added

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	Login	Enter the value into in the field	Sets the user name username to connect to the SIP-device (BasIP)	Latin, Cyrillic, and service characters	-NA	A line containing a sequence of any characters (letters, digits, service characters)
2	Password	Enter the value into in the field	Sets the password to connect to the SIP-device (BasIP)	Latin, Cyrillic, and service characters	-NA	A line containing a sequence of any characters (letters, digits, service characters)
3	IP address	Enter the value into in the field	Sets the IP address of the SIP-device (BasIP)	IP address	-NA	1.0.0.0–2550—255.255.255.255

Page tree

Versions Compared

Old Version 7

New Version 10

Key