Go to documentation repository
Page History
...
outline colors of the camera number and
...
surveillance window
| Note | ||
|---|---|---|
| ||
This section describes the default parameters of the color indication of the Surveillance surveillance window borderoutline. They can be changed You can change these parameters during the system configuration—see Configuring the interface of the Surveillance window. |
The color of the Surveillance surveillance window border indicates outline displays the current camera statusstate.
Color of the Surveillance surveillance window borderoutline | Camera statusstate |
Green | Camera is disarmed |
Yellow | Camera is armed |
Red | Camera is armed, an alarm event occurred is registered on the camera. OR Camera is disarmed, but one or more detection areas zones are alarmed, and an alarm event is detected in them—see also Indication of detection tool statusdetector status |
| Info | ||
|---|---|---|
| ||
The current state of cameras is saved in the STATES table of the Axxon PSIM database every 15 seconds. |
The outline The color of the camera number indicator border in the Surveillance surveillance window indicates displays the current status state of the video recording performed from the this camera.
Color of the camera number borderoutline | Camera statusstate |
Green | No video recording, camera Video isn't recorded. Camera is disarmed |
Yellow | No video recording, camera Video isn't recorded. Camera is armed |
Red | Video recordingis recorded |
The combinations combination values of theSurveillance surveillance window border outline color and the color of the camera number border outline are described in the following table.:
Color of the Surveillance surveillance window borderoutline | Color of the camera number borderoutline | Camera statusstate |
Yellow | Yellow | Camera is armed, no video recording is performed. Video isn't recorded |
Red | Red | Alarm event occurred is registered on the camera or in the alarmed detection areazone. Video recording is started by an alarm event, or the recording, started by Operatorthe operator's command before the alarm event registration, continues |
Green | Red | Camera is disarmed, but there video is recording recorded by Operatorthe operator's command or there is the post-alarm recording |
Yellow | Red | Camera is armed, recording by Operatorvideo is recorded by the operator's command or there is the post-alarm recording is done |
Green | Green | Camera is disarmed, no video recording is performed. Video isn't recorded |
Red | Yellow | Alarm event occurred is registered on the camera or in the alarmed detection areazone, but no video recording by alarm is donevideo isn't recorded when the alarm event is registered |
| Info | ||
|---|---|---|
| ||
If the auxiliary camera detector zone has been armed or disarmed, the border around the Surveillance window retains When you arm or disarm a camera by the additional detection zone, the surveillance window outline doesn't change its color, but after when an alarm event in the auxiliary zone the Surveillance window border becomes red. So, there is no indication of auxiliary detector zone arming and disarming for the camera by the frame of the Surveillance window. See also Indication of detection tool is registered on the additional detection zone, the surveillance window outline turns red. Thus, the indication of the camera arming or disarming by additional detection zones isn't performed with the surveillance window outline. See also Indication of detector status. |
Icons next to the camera number
The icon of the video signal absence absence 
appears below over the icon of "video camera number" only icon when there is no video signal. It can be in two cases: video camera is not connected or there is camera restartthe camera isn't connected, or the camera is restarted.
| Info | ||
|---|---|---|
| ||
The last video frame or blue screen (, depending on the video capture card) , is displayed in the Surveillance surveillance window if there is no video signal. |
The icon of the selected disk absence 
appears above the icon of "video camera number" if icon if you don't select the disk for archive storing is not selected (see Selecting the storage (see Select disks for video archive storage).
The icon of the overloaded disk 
appears above the icon of "video camera number" icon if there are frames skipped during the archive recording (it meansthat is, the FRAME_SKIPPED events are received, see CAM Camera). You can enable disable the indication of frames skipping with the ShowFrameSkippedStatus ShowoutlineSkippedStatus key, see Registry keys reference guide.
When you specify the incorrect camera type is given, the icon of disconnect disconnection with the camera camera 
appears above the icon of "video camera number" icon, and the frame of Surveillance surveillance window outline turns black.
Overview
Content Tools