Versions Compared

Old Version 1

changes.mady.by.user Yulia Morozova

Saved on

compared with

New Version Current

changes.mady.by.user Bahdan Tsiulkou

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Section


Column
width50%


Panel
borderColor#CCCCCC
bgColor#FFFFFF
titleBGColor#F0F0F0
borderStylesolid
titleOn this page:
Table of Contents



Column


Configuring the SIP-device

Before you start configuring the SIP-device connection to Axxon PSIM, it is necessary to you must configure the device itself. Each Configure rach SIP-device is configured individually according to the manufacturer's documentation, however, it is you must always necessary to perform the following basic steps:

  1. Specify the IP address of the Axxon PSIM server that acts as a the SIP server.
  2. Check or specify the SIP-device identification number (the number used for calls).
  3. Set the password for to connect to the SIP-server connection.
  4. If the SIP-device does not doesn't support dialing from the keyboard and has only one button for calling the concierge, it is necessary to you must configure this button to call the the Axxon PSIM operator (see Configuring SIP-operators on the SIP server of the Axxon PSIM's SIP server).

Configuring the SIP-device connection to Axxon PSIM

The To configure the connection of the SIP-devices connection device to the Axxon PSIM SIP-server is configured as follows, do the following:

  1. Create a the SIP-device object based on the SIP-terminal object of the SIP-server type (1).
  2. In the User ID field (1), enter the SIP-device identification number, i.e. , that is, the number to call it.

  3. In the Device IP address field (2), enter the SIP-device IP address. If you are not aren't going to send data to the SIP-device, there is no need to fill in this field is optional.

  4. In the Password field (3), enter the password specified on the SIP-device. The SIP-device with the specified identifier will be is connected to Axxon PSIM only if the passwords on the device and in Axxon PSIM are identical.

  5. The State field (4) indicates the current status of the SIP-device.
  6. From the Device type drop-down list (5), select the icon type used to display the device on the Map.
  7. From the Device priority drop-down list (6), select the priority of calls from this device when displayed on in the SIP panel window of incoming calls. The lower the number, the higher the priority, and, hence, the higher the call is displayed in the list. If you leave the field is left blank, the priority is considered minimal. Calls from devices with the same priority will be sorted by are sorted by the time of the call occurrence.
  8. Click the Apply button (7).

Configuring

...

video and audio

To configure the video and audio of Configure the SIP-device's video and audio in , do the following order:

  1. Go to the Video / Audio tab (1) on the settings panel of the SIP-device object.

  2. Set the Video switch (2) to the position corresponding to the video camera used for calls:

    1. Off — the video is not —the video isn't used during the call.

    2. SIP camera — a —the SIP-device camera connected via the SIP protocol is used. If the wrong device is selected by default in the Camera (3) drop-down list, change the selection. The corresponding Camera object may not be created in the Axxon PSIM objects tree at this step; in this case, it will be is created automatically after clicking the you click the Apply button.

    3. Other — any —any other camera from the Axxon PSIM hardware tree is used. In this case, select the name of the required Camera object from the Camera drop-down list (3).

  3. Set the Audio switch (4) to the position corresponding to the microphone used for calls:

    1. Off — the audio is not —the audio isn't used during the call.

    2. On — when making —when you make a call, the microphone of the SIP-device, displayed in the Microphone information field (5), is used. The corresponding Microphone object may not be created in the Axxon PSIM objects tree at this step; in this case, it will be is created automatically after clicking you click the Apply button.

  4. Click the Apply button (6).
    Info
    titleNote

    If necessary, the pre-configured missing Camera and Microphone objects

    5. will be

  5. are automatically created in the Axxon PSIM objects tree.

Configuring the tone DTMF commands

The setting of sending To configure the sending of tone messages to a the SIP-device (for example, a combination combinations for door opening a door) is carried out by setting ), configure the relay.

The To configure the relay of the SIP-device relays are configured in , do the following order:

  1. Go to the Relay tab (1) on the settings panel of the SIP-device object.
  2. Select From the type from the DTMF type drop-down list (2), select the type of tone signal:
    1. sip_info – signals —signals are transmitted in the SIP INFO message of the SIP protocol.
    2. sip_notify – signals notify—signals are transmitted in the SIP NOTIFY message of the SIP protocol.
    3. in_-band – the —the signal is transmitted as normal sound in an the audio stream.
    4. http_bas– —signals are transmitted over the HTTP protocol. When you select this tone type of tone is selected, the Device connection settings button (3) becomes active.  Click the button to open the device connection settings window:

      In this window, specify the Login, Password and IP address of the SIP device. If the port is different from the actual one (for example, it's 8180, not 80), then also specify the port in the IP address field also. If you leave the IP address field is left blank, then the IP address will be is taken from the session, and the port will be is presumed to be 80.
  3. In the Signal duration, ms field (4) set , enter the time period in milliseconds during which the command is to DTMF signal must be sent. This value is applied if duration is not set for a specific commandThe field is unavailable when you select the http_bas tone signal.
  4. In the Name field (5), enter the name of the command that is displayed on the SIP panel.

  5. In the Code field (6), enter the unique command code.

    Info
    titleNote

    If you use the http_bas tone type is selectedsignal, then enter a request according to the documentation of the SIP device in the the Code field, for example: GET access​/general​/lock​/open​/remote​/accepted​/1.

  6. Click the Applybutton (7).
    Info
    titleNote

    The corresponding Relay object

...

  1. is created in the Axxon PSIM hardware tree.

The Configuring the SIP-device of the Axxon PSIM's SIP server is configuredPSIM SIP server is complete.