Page History

The You can create the Sensor system object is created under the Video Capture Device on the basis of the Video capture device object.

The Sensor object is created and main parameters are set in the following orderTo create and configure the main parameters of the Sensor object, do the following:

1. Go to the Hardware tab in of the settings panel of  Axxon PSIM™  settings panel (1).
2. Create the Sensor system object under on the basis of the Video Capture Devicecapture device object or select the corresponding object in the object tree in on the Hardwaretab on the settings panel of  tab of the Axxon PSIM™  settings panel (2).
   

3. Specify When you create the Sensor object (3), you must specify the ID and , the name of the Sensor object and select the Video Capture Device object to become the parent of the Sensor object (3)capture device object based on which the Sensor object is created.

   Info
   title Note
   If you use the Sensorsensor-Relay relay card is used, then specify that in the Sensor object settings, you must specify the video capture card with on the ADC to of which the Sensorthe sensor-Relay relay card is connectedinstalled.

4. Select the channel number matching in accordance with the number of the output connector to which the sensor is connected physically (4).

5. In the group of switches, select the alarm mode at which the sensor generates an event: at switch on or at switch off. By default, the alarm at switch on mode is selected (5).
   The executive device corresponding to the Sensor system object operates in one of two modes: alarm at switch on or alarm at switch off.
    

   Info
   title Note
   Sensors connected to Panasonic IP-devices (of the i-Pro series ) trigger generate an event only at the switch off event.

   When For example, when you select the alarm at switch off mode is selectedfor the executive device of the Sensor type, the normal state of the sensor is openswitch on. When you switch it off, the sensor closesgenerates an event, it triggers and the corresponding actions set in Axxon PSIM are eventually performed in Axxon PSIM™.

6. In the
Hardware dropdown
7. Detector drop-down list, select the type of executive device that is used as
the detector in the guarded area
8. a sensor on the protected facility (6).
   The
Hardware
9. Detector parameter is used for selecting the icon that is displayed on the interactive map. This parameter is
essential
10. required for the better perception of information
(
11. by the operator that is displayed on the
map
12. Map as object icons
) by Operator and for real-time intercepting by Operator if
13. , as well as for the rapid operator reaction if such is required.
14. Types of detectors available for the Sensor system object are given in the table.
    

    Hardware	Description
    Infrared

Icon

15. The icon of the interactive map for the

16. motion

detectors

17. detector

    PIR

Icon

18. The icon of the interactive map for the

19. device installed on the ceiling of the

guarded area

20. protected facility

    Glass

Icon

21. The icon of the interactive map for the

22. device installed on the window of the

guarded area 

23. protected facility andresponding when the window is broken

    Fire

Icon

24. The icon of the interactive map for

the device

25. the device responding to

changes of heat conditions in the guarded area

26. the heat condition changes at the protected facility

    Window

Icon

27. The icon of the interactive map for

the 

28. the device installed

some distance away the window

29. at a distance from a window and responding when the window is broken

    Smoke

Icon

30. The icon of the interactive map for

the 

31. the device responding to the smoke

in the guarded area  

32. appearance at the protected facility

    Reed switch

Icon

33. The icon of the interactive map for the

34. device

responding

35. that responds to locking/

unlocking 

36. unlocking a window, door,

etc.

37. and so on

38. Click the Apply button to save the changes.

...

After you create the sensor in the objects tree, it

...

is in the "Armed" state. To change the

...

sensor state, use a macro (see the Creating and using macros section) or control the

...

sensor from the

...

map (see the Configuring the interactive map for object state indication and controlling the objects and Operations with sensors

...

sections). If you arm the

...

sensor,

...

the "Alarm" event appears when you switch on/switch off the

...

sensor depending on the alarm mode

...

setting—see step 5 above. If you disarm the

...

sensor, the "

...

Switch off"/"

...

Switch on" events appear correspondingly.