Page History

If you connect relays are connected to the Sensorsensor-Relay relay card, then you can create up to 4 four Relay objects can be created under on the basis of the Video Capture Devicecapture device parent object.

All the All Relay objects corresponding to relays connected to one Sensorone sensor-Relay relay card are to must be created in the Hardware object tree under on the basis of the Video Capture Devicecapture device object corresponding to the physical video capture card where the Sensorthe sensor-Relay relay card is installed.

At least one Camera object is to be created under For the relay to operate, you must create at least one Camera object based on the same Video Capture capture device object for relay to work.

If the Sensor-Relay card is installed on you install the sensor-relay card on the FS-5, FS-6 or FS-16 video capture card, then you can create the Relay objects are to be created under any Video Capture Device based on any Video capture device object within the hardware card.

If the Sensor-Relay card is installed on SC3B0N16 you install the sensor-relay card on the SC3B0N16 (WS216) video capture card, then you must create the Relay objects are to be created under based on the Video Capture Devicecapture device object with the 04 value number of the PCI - channel.

If the Sensor-Relay card is installed on you install the sensor-relay card on the FS-8 video capture card, then the you must create the Relay objects are to be created under based on the Video Capture Devicecapture device object with the 07 value number of the PCI - channel.

Relay objects can be relocated You can change the Relay object's position in the Axxon PSIM object tree. To change the parent Video Capture Device object of capture device objects for the Relay objects, change the value of the Video Capture Device object capture device parameter on the settings panel of the Relay object. The value of this parameter is to must correspond to the number of the the Video Capture Devicecapture device object ( in the object tree ) under which based on which you must place the Relay object is to be located. If the value of the Video Capture Device parameter is changed you change the Video capture device parameter on the settings panel of the the Relay object, then the object is moved to the branch of child objects of the corresponding Video Capture Devicecapture device object.

The next figure shows an example of locating placing the Relay objects in the object tree when two FS-6 (or FS-16) video capture cards are used with 4 four relays connected to the first 4/4 (or 16/4)  Sensor-Relay sensor-relay card installed on the first video capture card and 2 two relays connected to the second one are used. 

Configuring When you configure the Relay objects one is to specify in Axxon PSIM, you must assign the channel numbers of sensor connection to the Sensor-Relay card according to the numbers of the DO pins connections (interface lines with the executive device) to the sensor-relay card in accordance with the numeration of inputs of the DO sensor/relay connection connector on the card.

To change the channel numeration, use the the Channel Numbernumber list on the settings panel of the Relay object.

The When you use the 4/4 and 16/4 Sensor4 sensor-Relay relay cards allow connecting , up to 4 four relay connection channels are available according to the configuration of the license key file.

The figure below shows an example of the channel numeration configuration of 4 relays allocating the channel numeration when four relays are connected to one 4/4 Sensor4 sensor-Relay relay card installed on the FS-6 ( or FS-16 ) video capture card (4 ADCs for 4 Video Capture Device objectsfour Video capture device objects correspond to four ADCs).

Channels of the second (the next one) 16/4 Sensor4 sensor-Relay relay hardware card are numbered from 1 -to 4 according to the DI input connectors of the sensor/relay connection on the card.

Example of allocating the channel numeration configuration channel numeration of relays connected on to the second (the next one) 16/4 Sensor4 sensor-Relay relay card installed on the FS-6 ( or FS-16 ) video capture card (4 ADCs for 4 Video Capture Device objectsfour Video capture device objects correspond to four ADCs):