Page History

...

1. The button is used to switch to the archive to view and export video of the event.

2. The button is used to switch to the map layer where there is the source of the event is.

3. The button is used to escalate the event.

   Info
   title Note
   If the event has got the Escalated status, this event is displayed in the interface of the operator protocol of the higher level. If the Escalation button is inactive, it means that no superior interface is assigned to the current operator protocol.

   Several superior interfaces can be assigned to the operator protocol, but escalation is performed to one of them. If more than one superior interface is assigned, then before clicking the Escalation button, select the required operator protocol of the higher level in the drop-down list that can be found below the Escalation button.

4. The  drop-down list is used to group the display of events by region, event, or object.
5. The checkbox is used to enable a simple display of events at the bottom of the Current events tab.

6. The buttons are used to assign the type (status) to the event. You can change the names of buttons during system setup. If the system is configured accordingly, event processing buttons can be unavailable until you enter a comment. Also, if configured accordingly, the buttons can be missing when you select the row with the name of the event grouping.

7. The button is used to delay event processing once for a time period specified when configuring the operator protocol.

8. The button to open the help file for processing the selected event.

9. The field to enter a comment.

   

   The comment field also contains the information about the completed tasks from the checklist (see below). 

10. When you set the checkbox, the type assigned to the corresponding event is applied to all events in the Current events tab.

11. The checkbox is used for auto creation of a bookmark in the archive when the event is processed by the operator. The entered comment is used as the bookmark name.

12. The checklist contains the list of actions that must be performed by the operator during event processing.
    

...

1. If you don't select any value in the Group by drop-down list and don't set the Simple view checkbox, then the bottom of the Current events tab displays the cells, each of which corresponds to one event. The number of horizontal cells is determined by the width of the Operator protocol window. The information on the event and the frames from the camera linked to the object from which the event is received are displayed in the cell (see Connection of objects with cameras). The name of the corresponding camera is displayed on the frame. If there are several cameras linked to the object, you can use the buttons to scroll through frames.

   Info
   title Note
   To display event frames from the camera's embedded detectors, it It is not necessary to configure the connection between the embedded detector and the camera to display event frames from the camera's embedded detectors.

   

   
   The cell contains the following information:
   1. Name of the event in the system.
   2. Object that registered the event.
   3. Name of the Region object corresponding to the area where the event is registered.
   4. Date and time of event registration.
   5. Time left before the Unclassified event type is assigned to the event.

   6. Information about event escalation or additional parameters.

      Info
      title Note
      The You can set the list of additional parameters is set when configuring the the Operator protocol object (see Administrator's Guide).

2. If you don't select any value in the Group by drop-down list and don't set the Simple view checkbox, then the bottom of the Current events tab displays a simplified list of events without the frames from the camera:
   
   Each line corresponds to one event and contains the following information:
   1. Name of the event in the system.
   2. Object that registered the event.
   3. Date and time of event registration.
3. If you select any value in the Group by drop-down list, then the bottom of the Current events tab displays a list of groupings by the selected parameter. The list line contains the number of events in the grouping and the name of the parameter by which the events are grouped.
   
   To view all events from the group, click the button. To hide the grouped events, click the  button:
   
   The content of the expanded group depends on whether you set the Simple view checkbox or not. If you don't set it, the events are displayed as cells. If you set the Simple view checkbox, then a simplified list is displayed.

...

...