Page History

You can select and configure cameras for displaying in the Monitor interface window  window in two ways:

...

1. Separately. The settings panel of the Monitor object is used.
As a package. The
2. In bulk. The Add/Edit Camera Objects
dialog box is used.

...

1. window is used (the Range button), see Selecting and configuring video cameras

...

1. in bulk.

To select video cameras individually on the settings panel of the Monitor object, do the following:

1. Go to the List of cameras tab.
2. To select all cameras registered in the system, click the All button
(1)
3. .
   Image Modified
4. To add a separate camera, configure the following settings in the table
(2)
5. :
   1. From the drop-down list in the Number column, select the number of the
required
6. 1. camera.
As
7. 1.  As a result, the name of the selected camera will be automatically displayed in the Camera column.

   2. If multistream mode is enabled for the camera, in the Video stream drop-down list, select the number of the video stream that you want to display on the Monitor

(4)

8. 1. . If no stream is selected, the default stream is used.

      Info
      title Note
      Configuration of the Server video streams is described in

Configuration of

9. 1. Configuring the multistream video. The selected video stream is requested when receiving a video signal both from the Server and via the Videogate.

   2. By default, the Monitor receives a video stream through the Server. If it is necessary to get the video stream directly from the camera, not through the Server,
but directly
10. 1. from
the camera, in
11. 1. the Connection drop-down list, select Direct.

    2. If a video signal needs to be decimated for its transmission to the Client Monitor, select the required frame rate of the video signal from the drop-down list in the fps column. 

       Note
       title Attention!

It is strongly not recommended to use

12. 1. We strongly discourage you from setting additional decimation and/or compression

of the

13. 1. for video signals displayed on the Server Monitor, as

it will lead to the additional spending

14. 1. this results in unnecessary consumption of the Server resources

and deterioration of titleNote

15. 1. while the video image quality deteriorates.

Info

16. 1. Features of fps selection:

       1. The selected FPS value
should
17. 1. 1. must be less than the frame rate of the video digitising by a video capture card. Otherwise, the frame rate of the video signal will be the same as the FPS of digitising.
InfotitleNote
18. 1. 2. For the correct decimation of a video stream compressed using the H.264 or MPEG4 codecs, the FPS value
should
19. 1. 1. must be equal to the frame rate of the key frames specified in the device settings (IP
-
20. 1. 1. camera)
or
21. 1. 1. or Axxon PSIM settings (
see 
22. 1. 1. see Configuring video compression).
info

title	Note

24. 1. 1. Four streams for a chip are processed on SC300Q16 (FX4) video capture card. If the chip processes a stream without a signal (blue screen), then the total FPS is 10 (
4 x 2,
25. 1. 1. 4x2.5 FPS) for one chip.
    2. From the Hardware decoding drop-down list, select default CPU decoder (blank value), Nvidia decoder, or Intel Quick Sync. Selecting a hardware decoder increases the load on the corresponding CPU. 

    3. If video signal compression level needs to be changed for transmission to the Client Monitor, select the required level of video signal compression from the drop-down list in

the

26. 1. the Compression column. The compression level of the video signal increases from 0 (no compression) to 5 (maximum compression).

       Info
       title Note
       If you change the compression level

is set

27. 1. for the Client, the video signal on the Server

needs to

28. 1. will be pre-decompressed, which will result in a great load increase on the CPU of the Server.

    2. To change the algorithm of the video signal compression for transmission to the Client Monitor, select the required algorithm of compression from the Compressor drop-down list. If the compressor is selected, the value in the Compression list is

should

29. 1. must be selected as well.

       Info
       title Note
       Recompression of the video signal is performed on the Videogate side.

    2. If the Monitor
should
30. 1. must receive live and archive video from the selected camera via the Videogate object, select the name of this object from the drop-down list in the Gate column.

    2. If a video archive from the selected camera

should

31. 1. must be transmitted to the Monitor from the Backup archive object, select the name of this object from the drop-down list in the Backup archive column.

       Info
       title Note
       In case the access to the Backup archive is performed through the Videogate, the specified value

should

32. 1. must coincide with the selected value for this video camera

while

33. 1. when configuring the Videogate

object—see

34. 1. object—see Selecting and configuring the cameras for the Videogate module.

    2. If the selected video camera is used for video archive viewing from the edge storage, select the required Edge storage object from the Edge storage drop-down list.
    3. If the tansmission from the Backup archive object is performed via the Videogate object, select the name of this object from the drop-down list in the Videogate for Backup archive column.
    4. To enable smart search in the archive of the corresponding camera, select the VMDA metadata storage object corresponding to the VMDA tracks database intended to be used for smart search from the VMDA metadata storage drop-down list.

    5. If there is a fisheye or a panomorph lens on the camera (see Configuring fisheye cameras), in the Display type drop-down list, select the type of displaying video from the camera in the Surveillance window: virtual telemetry or panorama.

       Info
       title Note
       Conversion is enabled in the Video surveillance monitor when zooming

-

35. 1. in (see Mouse PTZ control) or in the function menu of the Surveillance window (

see

36. 1. see Enabling fisheye).

InfotitleNote

37. 1. This feature won't work if:

—
38. 1. • only alarm cameras are displayed on the monitor (see Configuring the display mode
for
39. 1. • of camera
boxes
40. 1. • windows);
—
41. 1. • PTZ control on the Video surveillance monitor is forbidden (see Setting the Telemetry control priority using the Monitor object).

       
       

    2. If it is necessary to start macros from the camera function menu in the Surveillance window, select the corresponding Macro objects from the Macro 1 and Macro 2 lists. See also Creating and using macros.
    3. The Guid column will automatically display the unique identifier of the selected camera. This value cannot be changed, it depends on the camera number.
    4. Repeat steps a-n for all required
video cameras.
42. 1. cameras. To add new cameras to the table use the down arrow button ↓ on the keyboard. To delete a row, use the Ctrl+Del key combination.
43. To save all changes, click the Apply button
(3)
44. .

Video cameras on the settings panel of the Monitor object are now selected.