Page History

x32: (x32)\Video
x64: (x64)\Video

ArchiveFps

1-24

1.0.0 and later

Sets the number of frames recorded to the archive (max.resolution). LiveFps and ArchiveFps parameters are not to exceed 24 in total.

x32: (x32)\Video
x64: (x64)\Video

DoubleStream

0, 1

1.0.0 and later

Defines whether asynchronous video display mode is enabled or not.

x32: (x32)\Video
x64: (x64)\Video

IpIntDrivers3

Brand name: Axis; Acti, etc.

1.0.0 and later

The IpIntDrivers3 string parameter is created and the names of brands that need 3.0 driver are listed.

x32: (x32)\Video
x64: (x64)\Video

IpIntDriverVersion

2, 3

1.0.0 and later

Defines the version number of loaded drivers:
2 – to load drivers version 2.0;
3 – to load drivers version 3.0;
This parameter has a high priority and cancels IpIntDrivers3 parameter.

x32: (x32)\Video
x64: (x64)\Video

LiveFps

1-24

1.0.0 and later

Sets the number of frames displayed in the 800x600 format. LiveFps and ArchiveFps parameters are not to exceed 24 in total.

x32: (x32)
x64: (x64)

LoadIpIntDirectly

0, 1

1.0.0 and later 

1 – enable IntegratedDevice via video.run. If the setting is enabled and at least one IntegratedDevice is added, then other IP video capture cards are disabled.

0 – IIntegratedDevice operates as a separate run-module.

The key is used to change a transport protocol used by the IP device.

Example of the key value: "ONVIF"="tcp" means that TCP protocol is used to transfer data via ONVIF.

See details in Changing Change the transport protocol used by IP - device

Example of the key value: "rtsp"="multicast" allows enabling Multicast mode of the RTSP Server. The object configuration is required in addition to the key.

See details in Configuring the RTSP Server module.

x32: (x32)\Video\MetadataTransportProtocols
x64: (x64)\Video\MetadataTransportProtocols

The name of camera driver (in the driver parameter of the

The key sets unused driver unload timeout for cameras. For instance, if camera brand is in several drivers, all of them are loaded at camera connection. To unload the unused drivers, set non-zero value to this key.

If the key is not created, then unused drivers are unloaded in 60 seconds.

0 – drivers do not unload (such behavior was in DriverPack versions older than the current one).

The key value that is > 0 sets unused driver unload timeout.

x32: (x32)\TELEMETRY
x64: (x64)\TELEMETRY

The key is used to enable the compatibility between presets in Axxon PSIM and previous versions of Drivers Pack, i.e. to decreasing the preset number by 1 when sending it to the driver.

0 – a new operation mechanism with presets the same as in Axxon One is in use in Axxon PSIM. If preset 1 is selected in Axxon PSIM interface, then value 1 is sent to the driver.

x32: (x32)\Video
x64: (x64)\Video

The key sets the number of streams created in FFmpegDecoder.

0 – decoder automatically selects the number of created streams.

>0 – sets the number of streams in use.

By default if there is no key or the value is incorrect, then value 1 is in use.

x32: (x32)\EventSources
x64: (x64)\EventSources

<brand>.<model> (for example, ONVIF.1_channel_device).

If all models of some manufacturer require a specific method of getting events, then there must be a string key named <brand> in the section.

Pull point

Meta data

Disable

By the date the documentation in created, this key is supported for three brands: ONVIF, RVi and IDIS. For models of these brands, the key is created automatically when the Drivers Pack is installed.

The key sets a method of getting data about the analytics and the sensors of the device:

• Pull point – getting events by http request of the camera
• Meta data – getting events from the metadata stream
• Disable – getting events is disabled.

enable

disable

The key is intended for setting up synchronization source (SSRC) for RTSP stream:

enable – SSRC check enabled;

disable – SSRC check disabled.

x32: (x32)\Video
x64: (x64)\Video

<brand>.<model>, for example, Tattile.ANPR Mobile

If all brand's models require a certain method of the timestamp adjustment, then the section must contain a string key with the name <brand>.

• InfrequentTs
• ValidDeviceTs
• None

DP 1.0.0

and later

The keys in this section specify the method of the frame timestamp adjustment.

If the key is not created, the timestamp transferred to the Axxon PSIM equals 0, and then the current time is set as its value.

The None value is used if it is necessary to disable the adjustment and transfer the timestamp received from the camera as is.

The ValidDeviceTs value means that the timestamp adjustment method is used before the timestamps transmission to the Axxon PSIM if the timestamp received from the camera differs from the current time by the value greater than the one specified in the MaxTimestampDeviation key (see below). After the adjustment, the timestamp calculated on the basis of the previous frame's timestamp and the time elapsed since its reception is transmitted to the Axxon PSIM.

InfrequentTs value discards the relative timestamps, transferring 0 to the Axxon PSIM instead (i.e., the current time is set as the timestamp value), and it also transfers the absolute timestamps with the ETimestampValidityFlag flag. This adjustment method should be used for the devices with the license plates recognition which transfer the separate frames to the external system, rather than a continuous video stream.

For some manufacturers, when installing the Drivers Pack, the keys with the necessary values are automatically created in the appropriate registry key.

The key is used for the ValidDeviceTs key value from the TsConverters branch (see above).

The key sets the maximum permissible deviation of the frame timestamp from the current Server time.

The key enables the interruption of the H.265 video decoding via the ffmpeg decoder in case of the slightest error in the video stream.

0 – if the video stream contains errors, then a buffer with artifacts will be received from the ffmpeg decoder.

1 – if the video stream contains errors, then an empty buffer will be received from the ffmpeg decoder.

The key sets the version of ONVIF services (only for ONVIF and ONVIF 2.X):

auto – get available versions and choose the latest if possible.

ver1 – use old versions of services.

ver2 – use new versions of services.

The key determines the source of the ONVIF services version (only for ONVIF and ONVIF 2.X):

getServices – get a list of services using the new interface.

getCapabilities – get a list of services using the old interface.

Disables looping files in a virtual video capture device of a Virtual bench type.

0 – videos in a Virtual bench virtual capture device are played in a loop.

1 – videos in a Virtual bench virtual capture device are played once.

See also Creating and configuring a virtual Video Capture Device.

"/cgi-bin/ptz.cgi?", "/stw-cgi/ptzcontrol.cgi?"

The key is required for PTZ operation with Hanwha Techwin IP-devices:

"/cgi-bin/ptz.cgi?" – for old models (not X-series)

"/stw-cgi/ptzcontrol.cgi?" –  for new models X-series

x32: (x32)\Video
x64: (x64)\Video

DP 1.0.0 and later

Compatibility: Axxon PSIM 1.0.0 and later

Time in seconds before the decompressor resets after an error. The value for the key should be selected empirically based on the stream parameters of a particular video camera.

Attention! It is recommended to change the value for the key only with the assistance of technical support.

The key sets the number of buffered decoded frames for the IntelQuickSync decoder.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

LPRDBsearchresultUnicodeBase64

0, 1

1

1.0 and later 

The key sets how to process message in param0<> for the SEARCH_RESULT event of the LPRDB ("External database") object – as ANSI line or Unicode line additionally encoded in base64.

0 – ANSI

1 – UnicodeBase64

x32: (x32-Monitoring)

x64: (x64-Monitoring)

PeakWorkingSetSizeQuota

>=0

100

1.0 and later

The maximum memory size in megabytes used by the process videosrv.exe on Agent Of Control. If the parameter is set to 0, then the check for the used memory is not performed.

Once a day, the Agent Of Control checks the size of the memory it uses. The check is performed at the time specified by the TimeOfCheckWorkingSetSize key (see below).

After exceeding the specified value, the videosrv.exe module is rebooted.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

TimeOfCheckWorkingSetSize

>=0

3

1.0 and later

Time to check memory usage in hours. Default value is 3 (3:00 AM). See also the PeakWorkingSetSizeQuota key description above.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

StoreVideoFiles

>0

3

1.0 and later

Time period for storage of not completely downloaded files on Agent Of Control. After the storage period is exceeded, the not completely downloaded files are deleted.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

run_core

0.1

1

1.0 and later

The key sets the Agent Of Control actions in case if the Axxon PSIM software is shut down.

0 – do not start the Axxon PSIM software

1 – start the Axxon PSIM software

x32: (x32-Monitoring)

x64: (x64-Monitoring)

socket_connect_tout

>=0

0

1.0 and later

The key defines TCP/IP connection mode with Server Of Control.

0 – blocking mode. Agent Of Control connects to Server Of Control without specifying connection timeout.

>0 – non-blocking mode.  Agent Of Control connects to  Server Of Control with a connection timeout set by the socket_connect_tout > 0 parameter in seconds.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

write_buffer_enable

0.1

1

1.0 and later

Data buffering while recording on disc when receiving video data on Server Of Control.  Agent Of Control transfers video data to Server Of Control in packages of 800 to 4096 bytes (4096 by default). When buffering is enabled, a 264 Kb block of memory is allocated to the Server Of Control for receiving video data, and data is saved to the disk when this memory block is full, not every time a packet is received from Agent Of Control.

0 – buffering is enabled.

1 – buffering is disabled.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

stop_data_by_trx

0.1

1

1.0 and later

The key determines the actions of Agent Of Control in case if, during the transfer of video data to ATM PSIM ARM, a financial transaction has begun on the ATM PSIM.

0 – video data transfer is not stopped.

1 – video data transfer is suspended until financial transaction if completed.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key specifies the port on the Server Of Control/Central Server Of Control used for connecting the clients.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

financial_trx_tout

>0

60

1.0 and later

Timeout for waiting for the financial transaction to complete in minutes. If after the start of the financial transaction during the time-out, there is no message from the ATM about its end, it will be considered to be completed.

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

The key enables special operation mode of the Monitoring PSIM software joint with Auto PSIM.

1 – the special operation mode of the Monitoring software joint with Auto PSIM is enabled.

Any other value – the special operation mode is disabled.

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

This parameter corresponds to the point of recognition. PlaceOfRecognitionN, where N is the ID of the LPR channel object.

1 – entrance.

2 – exit.

Note 1. The key is in use in special operation mode of the Monitoring PSIM software joint with Auto PSIM.

Note 2. The key is created at Agent Of Control

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

This parameter corresponds to the ID of a camera added to the recognition module. CamOfRecognitionN, where N is the ID of the LPR channel object. 

The value of this parameter corresponds to the Camera object ID specified in the LPR channel object settings.

Note 1. The key is in use in special operation mode of the Monitoring PSIM software joint with Auto PSIM.

Note 2. The key is created at Agent Of Control

x32: HKLM\SOFTWARE\BitSoft\VHOST\ULPR

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\VHOST\ULPR

The key enables the LP found in the database alarm both for Entrance and Exit recognition points.

0 – enables the LP found in the database alarm both for Entrance and Exit recognition points.

Any other value – the LP found in the database alarm is generated for Entrance recognition point only.

Note 1. The key is in use in special operation mode of the Monitoring software joint with Auto PSIM.

Note 2. The key is created at Server Of Control

x32: (x32-Monitoring)

x64: (x64-onitoring)

The key enables registration of the alarm with the time it occurred on the site.

0 – In the Alarm date field in the interface objects, the time of loading the alarm into the database after it is received from the Agent Of Control is shown, not the time of occurrence of the alarm on site.

1 - In the Alarm date field in the interface objects, the time of alarm occurrence on site is shown.

Note. The key is set on the Server Of Control.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

FileQueryEnable   

The key enables automated video clip loading.

0 – automated video clip loading is disabled.

1 – automated video clip loading is enabled.

Note. The key is created at Server Of Control and/or Additional Workstation

x32: (x32-Monitoring)

x64: (x64-Monitoring)

FileQueryPath

The key sets folder to share data with third party systems which is necessary for automated video clip loading.

Note. The key is created at Server Of Control and/or Additional Workstation

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key changes the Log Panel interface color theme.

0 - dark interface theme.

1 - light interface theme.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key specifies the path to the catalog of frames and video clips which were exported from the Monitoring PSIM interface during the live and archive video playback from a certain camera.

See Playing back live video and archive from a specific camera.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key removes the restriction on adding the same cameras for tracking in different Partitions Of Control.

0 - the restriction is enabled.

1 - the restriction is removed.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key activates the special  mode of Monitoring PSIM operation together with ACFA PSIM, as well as the ability to customize the long alarm description.

0 - Special operation mode is off.

1 - Special operation mode is on.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key changes the description of the long alarm Object disarmed in the Monitoring and Monitoring reports interface objects.

x32: HKLM\SOFTWARE\BitSoft\MonitorSSTV\Loader

x64: HKLM\SOFTWARE\Wow6432Node\BitSoft\MonitorSSTV\Loader

The key accelerates the speed of data loading from files to the MonitorSSTV database by activating the group operator of data loading if the database is installed locally.

0 - do not use the BULK INSERT operator (if the SQL Server is remote)
1 - use the BULK INSERT operator (if the SQL Server is local)

x32: (x32-Monitoring)

x64: (x64-Monitoring)

x32: (x32-Monitoring)

x64: (x64-Monitoring)

TimeoutForPostfix

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the operation mode of the Central Server Of Control software via FTP.

0 - Active mode.

1- Passive mode.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the statistics polling period in minutes for the Servers Of Control.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the log archiving period in hours of the Communication module (CentralNetServer.log)

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the maximum size of the communication module log file at which it begins to archive ignoring the LogArchPeriod parameter.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the log files archive retention period in months (CentralNetServer.log).

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the data retention period of closed errors and alarms in the ServerSSTV DB.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets the time in minutes, after which, if the data in the MonitorSSTV database is outdated, the corresponding indication on the Server Of Control/CSC will appear.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key disables the ability to accept alarms and force error closing.

0 - the ability to confirm alarms and force error closing is enabled.

1 - the ability to confirm alarms and force error closing is disabled.

If the key is set to 1, then:

• the area for comments and buttons for confirming the alarm are not displayed in the Reaction to alarm window; when you set the Confirm checkbox, nothing happens;
• when you click on the Force error closing button on the toolbar, the window with confirmation of force error closing does not open.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key sets low priority of the StreamViewer process when it starts.

0 − The StreamViewer process starts with normal (medium) priority.

1 − The StreamViewer process starts with low priority.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

x32: (x32-Monitoring)

x64: (x64-Monitoring)

If the continuous recording mode is enabled, the key sets the time interval of recording delay by camera in msec after it stops.

If the camera is armed, the key sets the time interval of camera arming delay in msec after it stops

x32: (x32-Monitoring)

x64: (x64-Monitoring)

If the parameter isn’t created or equals 0, the video data isn’t stored in the Monitoring database (MonitorSSTV or ServerSSTV).

If the parameter > 0, its value equals the number of days the video data should be stored in the Monitoring database. When this period is exceeded, the video data is deleted from the database

x32: (x32-Monitoring)

x64: (x64-Monitoring)

If you don't create the parameter or it equals 0, cameras aren't divided into groups

If the parameter > 0, its value equals the number of cameras in the group

x32: (x32-Monitoring)

x64: (x64-Monitoring)

If you don't create the parameter or it equals 0, the transmission of the LPs' blacklist is disabled.

If the parameter value is 1, the transmission of the LPs' blacklist is enabled

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key determines the connection port number of the Server of Control module to all Agent of Control modules

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key determines the connection port number of the Server of Control module to a certain Agent of Control module

For example, for the Agent of Control module with ID=550016, the used parameter is called TcpPortForBlackList550016

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key determines the number of hours after which the video information that appears in the Video data window can be deleted.

The key is installed on the computer with the Server of Control module.

If the parameter equals 0, the video data is deleted as usual after 30 days.

If the parameter >0, the irrelevant data is deleted after this number of hours

x32: (x32-Monitoring)

x64: (x64-Monitoring)

The key hides the camera IP address in the Reaction to alarm window when you press the Camera button on the control panel:

0—the camera IP address is displayed

1—the camera IP address is hidden

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the camera's menu.

0 - The menu is displayed.

1 - The menu is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Arm menu option.

0 - The Arm menu option is displayed.

1 - The Arm menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Start recording menu option.

0 - The Start recording menu option is displayed.

1 - The Start recording menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Camera menu option.

0 - The Camera menu option is displayed.

1 - The Camera menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Show titles menu option.

0 - The Show titles menu option is displayed.

1 - The Show titles menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Processing menu option.

0 - The Processing menu option is displayed.

1 - The Processing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Export menu option.

0 - The Export menu option is displayed.

1 - The Export menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Deinterlacing menu option.

0 - The Deinterlacing menu option is displayed.

1 - The Deinterlacing menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Zoom-in menu option.

0 - The Zoom-in menu option is displayed.

1 - The Zoom-in menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Contrast menu option.

0 - The Contrast menu option is displayed.

1 - The Contrast menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Detector mask menu option.

0 - The Detector mask menu option is displayed.

1 - The Detector mask menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Sharpen menu option.

0 - The Sharpen menu option is displayed.

1 - The Sharpen menu option is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Archive button.

0 - The Archive button is displayed.

1 - The Archive button is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the time.

0 - The time is displayed.

1 - The time is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the camera name.

0 - The camera name is displayed.

1 - The camera name is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key hides the Menu button.

0 - The Menu button is displayed.

1 - The Menu button is hidden.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key disables the control over the CamMonitor component using the hotkeys available for Video Monitor (see Video surveillance monitor).

0 - The control over the CamMonitor component using the hotkeys is enabled.

1 - The control over the CamMonitor component using the hotkeys is disabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key enables the Telemetry control using the CamMonitor component (see Telemetry control).  

0 - The Telemetry control using the CamMonitor component is disabled

1 - The Telemetry control using the CamMonitor component is enabled.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key activates the Delete menu item which is used to remove the recordings from the archive (see Deleting video recordings from the archive).

0 - The Delete item is hidden.

1 - The Delete item is displayed.

x32: HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\CamMonitor

x64:HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\CamMonitor

The key activates the Protect menu item which is used to protect the archive recordings from rewriting (see Protection of separate record and disable of protection).

0 - The Protect item is hidden.

1 - The Protect item is displayed.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

RequestFullStatisticOnStartup 

By default, the Central Server Of Control requests a complete package of statistics from all Servers Of Control only once, when it first connects to the Servers Of Control.

The key activates the request on the Central Server Of Control for a complete statistics package from all Servers Of Control every time the CentralNetServer.exe communication module is launched.

0 - disabled.

1 - a complete statistics package will be requested from all Servers Of Control each time the CentralNetServer.exe communication module is launched.

Attention! Requesting a complete statistics package is a resource-intensive operation. It is only necessary to activate this key if absolutely necessary.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

RequestFullStatistic[N]

Note. [N] is the internal identifier of the Server Of Control object in Axxon PSIM

By default, the Central Server Of Control requests a complete package of statistics from all Servers Of Control only once, when it first connects to the Servers Of Control.

The key activates the request for a complete statistics package from a specific Server Of Control once. The request will be executed when the CentralNetServer.exe communication module is launched, and the value of this key will automatically change to 0.

0 - disabled.

1 - a complete statistics package from a specific Server Of Control will be requested once when the CentralNetServer.exe communication module is launched.

Attention! Requesting a complete statistics package is a resource-intensive operation. It is only necessary to activate this key if absolutely necessary.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

Sets the path to the FTP directory on the Server Of Control for working with the Central Server Of Control.

x32: (x32-Monitoring)

x64: (x64-Monitoring)

DISK:\Export\

, where DISK is the drive on which the operating system is installed