The settings panel of the SIP-device system object is shown in the figures below. The description of the settings parameters is given in the tables.

№

Parameter

Method for setting the parameter value

Parameter description

Representation

Default value

Value range

1

Identification number*

Automatically

Displays the identification number of the SIP-device system object in the system

Numbers, letters, periods, hyphen, dash, and underscore

NA

Depends on the number of the SIP-device objects in the video surveillance system with distributed architecture

2

Name*

Enter the value in the field

Sets a name of the SIP-device object in the video surveillance system with distributed architecture

Latin, Cyrillic, and service characters

SIP-terminal

A line containing a sequence of any characters (letters, digits, service characters except > and < characters), case-insensitive.

Number of characters—from 1 to 60

3

Disable

Set the checkbox

Disables the SIP-device object in the video surveillance system with distributed architecture

Boolean type

Clear

Set—the SIP-device object is disabled and isn't used

Clear—the SIP-device object is enabled and used

4

SIP-terminal

Select the value from the list

Sets the SIP-terminal parent object for the given SIP-device object

Name of the SIP-terminal objects registered in the system

Name of the SIP-terminal parent object

Depends on the number of the SIP-terminal objects in the system

5Device typeSelect the value from the listSets the icon type to display the device on the MapNames of the available icon typesNA
  • Empty line (no value);
  • touch panel;
  • speaker;
  • camera;
  • microphone;
  • default
6Device prioritySelect the value from the list

Sets the priority of a call from this device in the incoming calls window of the SIP panel

Sequence of numbersNA

From 1 to 10.

  • The lower the number, the higher the priority and, accordingly, the higher the display in the list;
  • If the field is left blank, then the priority is considered to be minimal;
  • Calls from devices with the same priority are sorted by the time of the call

The Device connection settings group

7User IDEnter the value in the fieldSets the SIP-device identification number, that is, the number to call itSequence of numbersNA>=0
Device IP addressEnter the value in the field

For the SIP-server terminal type only.

Sets the SIP-device IP address

IP addressNA1.0.0.0—255.255.255.255
PasswordEnter the value in the field

For the SIP-server terminal type only.

The password specified on the SIP-device

Latin, Cyrillic, and service charactersNAA line containing a sequence of any characters (letters, digits, service characters)
StateAutomatically

For the SIP-server terminal type only.

Displays the SIP-device state

NANANA

*Name of the element isn't displayed in the settings panel of the given object.

The Video/Audio tab (only for the SIP-server terminal type)

№

Parameter

Method for setting the parameter value

Parameter description

Representation

Default value

Value range

1VideoSet the switch to the required positionSets the camera used for callsSupported options of camera usageOff
  • Off—the video isn't used during the call;
  • SIP camera—a SIP-device camera connected via the SIP protocol is used;
  • Other—any other camera from the Axxon PSIM hardware tree selected from the Camera drop-down list is used
2CameraSelect the value from the listSets any video camera used for calls

Name of the Camera objects registered in the system

NADepends on the number of the Camers objects in the system
3AudioSet the switch to the required position

Enables the audio during a call

Supported options of audio usageOff

Off—the audio isn't used during the call

On—the microphone of the SIP-device is used during the call

4MicrophoneAutomaticallyDisplays the name of the Microphone object corresponding to the SIP-deviceNANANA

The Relay tab (only for the SIP-server terminal type)

№

Parameter

Method for setting the parameter value

Parameter description

Representation

Default value

Value range

1DTMF typeSelect the value from the listSets the type of the tone signalSupported signal typessip_info
  • sip_info—signals are transmitted in the INFO message of the SIP protocol;
  • sip_notify—signals are transmitted in the NOTIFY message of the SIP protocol;
  • in_band—the signal is transmitted as normal sound in an audio stream;
  • http_bas—signals are transmitted via the HTTP protocol separately from the voice stream
2Signal duration, msEnter the value in the fieldSets the time period in milliseconds during which the DTMF signal must be sentSequence of numbersNA>0
3Device connection settingsNAOpens the Device connection settings pop-up window only when the http_bas type of tone is selected NAInactive by defaultNA
4NameEnter the value in the fieldSets the name of the command that will be displayed on the SIP-panel Latin, Cyrillic, and service charactersNAA line containing a sequence of any characters (letters, digits, service characters)
5CodeEnter the value in the fieldSets the unique command codeSequence of numbers or HTTP request (for http_bas)NA

A line containing a sequence of numbers or HTTP request

The table below describes the fields of the Device connection settings window.

№

Parameter

Method for setting the parameter value

Parameter description

Representation

Default value

Value range

1LoginEnter the value in the fieldSets the username to connect to the SIP-device (BasIP)Latin, Cyrillic, and service charactersNAA line containing a sequence of any characters (letters, digits, service characters)
2PasswordEnter the value in the fieldSets the password to connect to the SIP-device (BasIP)Latin, Cyrillic, and service charactersNAA line containing a sequence of any characters (letters, digits, service characters)
3IP addressEnter the value in the fieldSets the IP address of the SIP-device (BasIP)IP addressNA1.0.0.0—255.255.255.255